2023 Case IH Pull-Type Disc Mowers TD103
- Year 2023
- Make Case IH
- Model Pull-Type Disc Mowers
2023 Case IH Pull-Type Disc Mowers TD103
The Case IH TD103 pull-type disc mower features a smooth ride, clean cut, superior trailing ability, low transport height, and easy tractor hookup.
The Case IH TD103 pull-type disc mower features a smooth ride, clean cut, superior trailing ability and narrow transport width, plus easy tractor hookup using a simple clevis hitch.
Features may include:
Superior Crop FlowThe Case IH TD103 pull-type disc mower features a modular cutterbar design for superior crop flow that reduces streaking and ensures quick mowing.
Versatility and Convenience- Quick change knives cut change time in half. Simply use the provided tool, no wrenches necessary.
- Crop deflector shields located behind each end of the cutterbar to direct cut crop into a wide swath inside the tire path
- Two end discs that co-rotate to provide a narrower swath
- Able to adjust swath from 60 in–95 in (1.5 m–2.4 m)
- Left cutterbar shield is hinged for easy service access
- Shock protection to minimize repair expense
- Discs protected from internal gear damage by the drive hub
- 3-year cutterbar warranty includes one full-year of base factory warranty, plus two additional full years and unlimited hours of extended factory disc cutterbar warranty
- Overload protection is standard
- Primary PTO uses an 80-degree constant velocity joint at the tractor end to permit tight turns, reduce noise and extend service life
- Standard tractor tire bumpers protect PTO driveline and tractor tires
Tilt is adjustable from 2–10 degrees using a mechanical turnbuckle.
Easy Transport- Attaching and detaching the mower from the tractor is easily accomplished with a simple clevis hitch . The TD103 can be pulled by lighter-weight tractors , as weight is pulled versus carried on a 3-point hitch.
- Transport width is just 10 ft 10 in (3,300 mm) when end shields are folded
- Removable parking jack stand is stored on top of tongue assembly
- Hydraulic tongue swing cylinder powers the unit from transport to operating position
- Has a 12-in (305-mm)-minimum cutterbar ground clearance in transport position
- Hinged right-side cutterbar shield folds up for narrow transport
- Safety tow chain standard
- Low transport height eliminates the need for implement lights
PTO
PTO Power, Rated Engine Speed
Disc @ Rated PTO: 2,835 rpm | Minimum Required: 60 hp
Drivetrain
Driveline
Protection: Slip clutch and overrunning clutch assembly @ rear of PTO shaft
Wheels & Tires
Tires, Front Specification
Tubeless Ag Rib Implement: 27×9.5-15 6PR
Operational
Operating Speed
Input: 540 rpm | Max. Transport: 20 mph (32.2 kph)
Hydraulics
Hydraulic Type
Circuits Required: 2
Minimum Hydraulic Pressure
Relief Required: 1,500 psi (103 bar)
Chassis
Hitch/Type
Drawbar Requirements – ASAE ASAE Category 2 drawbar
Dimensions
Dimensions
1.375 in. (35 mm)
Cutting Width
10 ft. 4 in. (3.15 m)
Width
Cutting: 95 –3.2 in. (24 – 81 mm) | Swath: 95 in. (2.4 m)
Transport Width
10 ft. 10 in. (3.3 m
Overall Width
16 ft. 4 in. (4.9 m)
Transport Length
15 ft. 8 in. (4.8 m)
Length
Operating: 15 ft. 3 in. (4.6 m)
Transport Height
62 in. (1.6 m)
Ground Clearance
w/ Header Fully Raised: 11 in. (279 mm)
Weights
Weight
Operating: 2,610 lb. (1 186 kg)
Features
Features
Number of Discs: 8 | Cutterbar Shear Protection: Standard - Frangible splines in disc drive hub | Cutterbar Flotation Vertical and lateral, adjustable springs | Splines: 6-Splines
Cutterbar Type
Modular
Knife Quantity
Per Disc: 2